ORDER NO. CPD0706228C1Notebook Computer© 2007 Matsushita Electric Industrial Co., Ltd. All rights reserved.Unauthorized copying and distribution is a
2. Names and Functions of Parts2-1A : Speaker B : Multimedia pocketC : SD Memory Card slotD : Battery packE : Headphone jackYou can connect headphones
2-2A : Hard disk driveB : Smart Card slot <Only for model with Smart Card slot> C : ExpressCard slot D :PC Card slot E : IEEE 1394 interface co
3 Block Diagram3-1Processor Processor System Bus System Bus PM965 PM965 (1.05V) Memory Interface Host Hub Bridge PCI ExpressAGTL+ AGTL+ 64bit 800 MH
4-14.1.4 Diagnosis Procedure
4.2. Troubleshooting Please take note of the following two points with regard to troubleshooting: 1. Know-how of diagnosis upon occurrence of heavy
5 Power-On Self Test (Boot Check) Outline of POSTThe set has a boot check function called POST (Power-On Self Test) in it. The condition of the main b
6 List of Error Codes <Only when the port replicator is connected>The following is a list of the messages that BIOS can display. Most of them
Troubleshooting02D0 System cache error - Cache disabledContact Panasonic Technical Support.02F0: CPU ID:CPU socket number for Multi-Processor error.0
7 Self Diagnosis Test7-1 As for the self-diagnosis test(PC-Diagnostic utility) to use this model, a standard test and the enhan
7-2-As for the device under the diagnosis, blue and yellow are alternately displayed at the left of the icon.- The diagnosis result of the device gree
7-3 Start the standard test Do not test Please begin testing clicking
3. Test Item and Division of trouble7-4CPU /SYSTEMPlace with possibili-ty of breakdownStanardTest itemEnhan-cingContent of standard test Content of en
Test ItemStandard EnhancedContent of Standard Test Content of Extend TestThe place with possibility ofbreakdownTouch ScreenIt is confirmed not to find
8 Wiring Connection Diagram8-1CN4300CN22CN9000CN6503CN27CN4400JK3004JK3003MicrophoneHeadphoneSERIAL PCBSW LED MDC PCBMAIN PCBBT PCBSD PCBSDCN3401SC R
9-19 Disassembly/ReassemblyNote:Power off the computer. Do not shut down to the Suspend or hibernation mode.Do not add peripherals while the computer
9-29.1.2. PreparationBefore disassembling, be sure to make the following prepara-tions.• Shut down Windows and turn off the power.• Disconnect the AC
9-39.1.5. Removing the Tilt Panl Ass’y1. Turn the Cover down and pull the Tilt Panel in the direc-tion of arrows.2. Remove the five Screws <N202>
9-49.1.7.1. Wireless LAN Module1. Remove the two Screws <N2> and two Cables(Gray andBlue).2. Pull out the Wireless LAN Module in the direction o
9-59.1.9. Removing the LCD unit, InverterAss’y and ANTENNA PWB L,R1. Remove the two LCD Rubbers and five LCD Sheets.2. Remove the five Screws <N4&g
9-69.1.11. Removing the Modem1. Disconnect the Cable from the Connecor(CN4200).2. Remove the two Screws <N2>, and remove the Modem.3. Remove the
LASER SAFETY INFORMATIONFor U.S.A.Class 1 LASER-ProductThis product is certified to comply with DHHS Rules 21 CFR Subchapter J.This product complies w
9-79.1.14. Removing the Top Cover1. Remove the Gasket.2. Remove the Screws <N2>, <N4>, <N9> and ten Screws<N14> 3. Turn the un
9-89.1.17. Removing the WWAN PCB1. Disconnect the Cables(Gray and Blue) from the WWANPCB.2. Remove the two Screws <N2> and the Screw <N9>
9-99.1.20. Removing the KBD Earth Plate1. Remove the Tape in the direction of arrow.2. Remove the four Screws <N4> and two Screws <N13>,an
9-109.1.23. Removing the Hinge Support L andMP Hold Plate1. Peel off the three Tapes and remove the two Cables(Grayand Blue). 2. Remove the six Screws
9-119.1.27. Removing the SERIAL PCB1. Remove the two Screws <N1> and Hex Spacer.2. Remove the SERIAL PCB.Screw <N1> : DFHE5035ZB9.1.28. Re
9-129.2. Reassembly Instructions9.2.1. Attention when CF-52 series is repaired• Please execute writing BIOS ID when you exchange the Main Board.• You
9-13 Setting of Main PCB before assembling.
9-14
9-159.2.3. Setting the SERIAL PCB1. Set the SERIAL PCB to the computer. 2. Fix the SERIAL PCB using the two Screws <N1>. No1, No.23. Tighten the
9-169.2.5. Setting the Fan Ass’y1. Fix the Fan Case Plate to the Fan Case using the three Screws <N2>.2. Fix the Fan to the Fan Case using the t
9-189.2.6. Setting the SC RELAY PCB and HDD Hold Plate1. Set the SC REALY PCB to the HDD Hold Plate, and fix it using two Screws <N2>. No.1, No.
9-199.2.7. Setting the Battery Connector Ass’y1. Fix the Batt Con Holder to the FPC Batt using the two Screws <N5>. 2. Fix the Batt Con Holder t
9-209.2.9. Setting the Hinge Cover R1. Place the Cable through the rectangled hole of Hinge Support R and connect the Cable to the Connector (CN7).2.
9-219.2.10. Setting the KBD Earth Plate1. Set the KBD Earth Plate to the computer.2. Fix the KBD Earth Plate using the four Screws <N4>. No.1 to
9-229.2.11. Setting the PWR BATTERY LED PCB1. Connect the Cabel to the Connector(CN4400), and insert it to the computer.CN4400CablePWR BATTERYLED PCBB
9-239.2.12. Setting the AUDIO PCB1. Connect the Cable to the Connector(CN3000).2. Set the AUDIO PCB to the computer, and fix it using the two Screws &
9-249.2.13. Setting the WWAN PCB1. Connect the FPC to the Connector(CN7002).2. Set the WWAN PCB, and fix it using two Screws <N2> and the Screw
9-259.2.14. Setting the SD PCB1. Connect the FFC to the Connector(CN4300).2. Set the SD PCB to the Top Cover, and fix it to using the two Screws <N
9-269.2.16. Setting the Top Cover1. Connect the KBD FPC and FFC to the Connectors(CN22 and CN23), and place the Top Cover on the computer.2. Fix the T
9-279.2.17. Setting the Keyboard1. Connect the FPCs to the Connector on the KBD FPC.2. Place the Keyboard Lid Plate on the Top Cover, and fix it using
9-28 Caution for when assembling the Keyboard.
9-299.2.18. Setting the Speakers1. Place the Speakers on the computer.2. Connect the Cables to the Connector(CN4202 and CN4203).3. Paste the Tape on t
9-30 How to paste the Tape
9-319.2.20. Setting the Handle Ass’y1. Assemle the Handle Ass’y (Grip Upper, Grip Lower, Handle Base L, Handle Base R, Handle Ring and Handle Pom), an
9-329.2.21. Setting the LCD Unit, Inverter Ass’y and Antenna PWB L, R1. Set the LCD Unit to the LCD Rear Cover2. Fix the Inverter Ass’y using the Scre
9-33 Setting of LCD unit ass’yLCDLCD DAMPER ALCD DAMPER BLCD DAMPER CLCD DAMPER DLCD Gap within 0.5mmGasketUsing JIGUsing JIGLCD CABLELCDInsert LCD
9-3458mmADHESIVE TAPE BADHESIVE TAPE BDo not exceedthe edge.Do not exceedthe edge.Do not exceedthe edge.ADHESIVE TAPE A
9-35Attention: The heat-resistant adhesive tape shall be stuck onto the part surely.Tape shall not cover the round holeAlong the slot2
9-36LCD ASS'YNote: Paster shall be firmly stuck andNote: Paster shall be firmly stuck anddoes not float.does not float.SHEETThere are total 12 ga
CONTENTS 1. Specifications ··················································································································1-1 2.
9-389.2.22. Setting the Display Unit, BIOS HIGH PCB and SW LED MDC PCB1. Set the Display Unit to the computer, and fix it using the four Screws <N4
9-396. Fix the SW LED MDC PCB using the six Screws <N2>. No.1 to No.6Screw<N2> : DFHE5122YAScrew <N4> : DRHM0093ZA Arranging the Cab
9-40
9-41 Arranging the Speaker Cables when assembling the SW LED MDC PCB.9.2.23. Setting the Wireless LAN Module, BIOS PCB and ROBSON Cover1. Put the Wir
9-429.2.24. Setting the DIMM Memory Card and DIMM Cover1. Put the DIMM Memory Card into the connector.2. Close the right and left Hooks, and paste the
9-432. Open the Cover, push the Tilt Panel Ass’y into the computer until it clicks.Screw <N202> : DRSB2+4FKLT Caution for when assembling the Ti
9-449.2.26. Setting the HDD1. Connect the HDD FPC Ass’y to the HDD.2. Insert the HDD Ass’y into the HDD Damper.3. Set the HDD Ass’y into the HDD Case
CF-52AJYZDZM10 Exploded ViewK140N2EN2EN2EN2EK121N2BE39HN2EN12EEN202EN202K151HN8EN202K214K213K212K212K215K216K217E201K218N2EN2EK211E5K155E34N2K154K33H
CF-52AJYZDZMK142K105K106K104K105K104K47K157K132K103K93K93-4K95K94K93-1K93-2K99K98E32E30K153K97K158K142K156K101K100 K102K73K96K143K157K141K123K122K146K
1. Specifications1-1This page provides the specifications for the basic model CF-52AJCBDBM / CF-52BJCBZBM / CF-52AJCHDBM / CF-52CCABXBM / CF-52DCABZBM
CF-52AJYZDZMK92-2K92-5K92-1K173K173IK172IK172K92-6K92-3Screw tightening torque0.18 ± 0.02 N.m(1.8 ± 0.2 kgf.cm)0.9 ± 0.05 N.m(9 ± 0.5 kgf.cm)0.2 ± 0.0
CF-52AJYZDZMBN15HN4HN4HN4HN4HN4K28K28K29K29K29K29K9K24K25K9K10K19K19E40K1K8K2K3K7K4E42K5K6EN12K20K21E35E41K22EN2K18K17K15HN4N4K13K12N4HN4EN2EN2E16E16-
Replacement Parts ListCF-52AJYZDZM NRP: Non Reusable PartsPART NO. DESCRIPTION Q'TYE1 DL3U11616AAAPCB, MAIN HIGHRTL 1E2 DL3U21616AAAPCB, AUDIORTL
P5 DFPE0875ZCTACCESSORY HOLDER1P6 DFPK1234ZATPACKING CASE1P7 DFPH0077ZATPROTECTION SHEET1P8 DFPP0136ZATPROTECTION BAG1K1 DFHR3G84ZBLCD DAMPER ANRP 1K
K62 DFHR3G78ZAFIN DUCTNRP 1K63 DFMC0895ZAEARTH PLATE PORTRE1K64 DFHE1061ZAGASKET-6-6-20NRP 1K65 DFHR3G83ZABOTTOM WP CUSHIONNRP 1K66 DFUN0056ZAPORT RE
K114 DFHG2034ZB-0FOOT RUBBERNRP 1K115 DFHE1089ZAGASKET-3-3-65NRP 1K116 DFHE1088ZAGASKET-65TSV2.5-1.5-20NRP 1K117 DFHR6342ZBMODELAN HOLDER-11K118 DFMX1
K212 DFGE0132ZB-0CENTER COVER NET 2K213 DFGX0493ZA-0TILT PANEL 1K214 DFHR3H21ZATILT PANEL SHEET 1K215 DFHR3H77ZCTILT PANEL WP SHEET 1K216 DFHR3H78ZBT
Replacement Parts List CF-52AJYZDZMPART NO. DESCRIPTIONQ'TYMAIN PCBIC 1 C2GBD0000033 CPU 1IC 2 C1CB00002803 CHIPSET PM 1IC 4 C1CB00002746 CHIPSET
C 41, 107, 110, 194, 195,236, 312, 328, 334, 336,339, 400, 416, 471, 473,486, 487, 499, 546, 547,560, 583F1J0J4750019 CAPACITOR, 6.3V, 4.7µF 22C 45, 4
C 420, 1005 F1G1H271A495 CAPACITOR, 50V, 270pF 2C 434, 435, 436, 437, 496,503, 523, 524, 529, 530,592, 616, 617, 632, 633,634, 635, 1102, 1177F1H1A105
1-2Model No. CF-52AJCBDBM / CF-52BJCBZBM /CF-52AJCHDBMCF-52CCABXBM / CF-52DCABZBM Battery Pack Li-ion 11.1 V, 7.65 AhOperating Time*14Approx. 3.5 hour
CN 1000 K1KB40AA0217 CONNECTOR 1D 2, 3, 10, 17, 18 MA2J72900L DIODE 5D 4, 7, 29, 1033, 1039, MA3J741E0L DIODE 6D 8, 9, 22, 23, 30, 31, 33, B0KB0000004
JK 1000 S K2EEYB000001 JACK 1JK 8101, 8102 K1QZA1AE0001 CONNECTOR 2L 1 G1C91NM00001 INDUCTOR 1L 4 G1C1R0Z00002 INDUCTOR 1L 5, 7, 8, 12, 17, 67, 68 J0
R 10, 11, 31, 333, 334,335, 336, 341, 342, 343,344D1BA1000A023 RESISTOR, 1/16W, 100Ω 11R 14, 16 D1BA27R4A023 RESISTOR, 1/16W, 27.4Ω 2R 15, 17, 36, 3
R 159, 163, 366 D1H85604A024 RESISTOR ARRAY 3R 168, 169, 206, 207 D0GA150JA023 RESISTOR, 1/16W, 15Ω 4R 173, 187, 188, 203, 205,222, 264, 375, 423, 43
R 1011 D1BA3093A023 RESISTOR, 1/16W, 309KΩ 1R 1012 D1BA1052A023 RESISTOR, 1/16W, 10.5KΩ 1R 1013 D1BA2151A023 RESISTOR, 1/16W, 2.15KΩ 1R 1015 D1BA20
C 3036 F1G1C104A042 CAPACITOR, 16V, 0.1µF 1C 3037, 3038 F1G1H1010005 CAPACITOR, 50V, 100pF 2C 3039, 3040 F1H1A225A039 CAPACITOR, 10V, 2.2µF 2C 3047
Q 4300 UNR9113J0L TRANSISTOR 1R 4300 D0GD101JA052 RESISTOR, 1/8W, 100Ω 1R 4301 D0GA101JA023 RESISTOR, 1/16W, 100Ω 1SW 4301 K0ZZ00000619 SW 1PWR BATT
L 5001 J0JJC0000021 INDUCTOR 1L 5003 G1C6N8JA0024 CHIP INDUCTOR 1Q 5000 B1GBCFNN0042 TRANSISTOR 1Q 5001 B1DHDC000028 TRANSISTOR 1R 5000, 5001 D0GA104J
1-3*11MB = 1,048,576 bytes*2You can physically expand the memory up to 4096 MB, but the total amount of usable memory available will be less depending
Komentarze do niniejszej Instrukcji